Stenner S128 1:128 rate 10oz/min 60psi max 120v 60hz 3/8" white Tantalum spring, fkm seate & o-ring

Stenner Pump Company

$1,021.99
(No reviews yet) Write a Review
SKU:
PM-CFP-S4M8XAA3011
Adding to cart… The item has been added

Activated by a dry contact pulse water meter, the S128 automatically injects solution into the water line proportional to the system water flow at a ratio of 1 ounce of solution to 128 ounces of process water. As the pump registers dry contacts, it delivers the precise ratio.

The pump has three speeds to automatically adjust the injection rate when the water system flow rate increases or decreases. This flow response design allows the pump to evenly and proportionally inject solutions especially at low flow rates.

  • Potentiometer: Prime, 1 PPG, 1 PPL, 10 PPG, Reset Tube Timer, Standby
  • Output Relays: Signal Repeater Leak Detect, Drive Fault, Low Level
  • LED Indicators: Leak/Fault, Overrun, Change/Level, Power/Standby
  • Clear cover on control panel for moisture protection
  • Enclosed housing with NEMA 4X rating

The built-in signal repeater relay repeats the pulse signal from the water meter to another pump or house controller. If using a meter to register water consumption to the house controller, an additional meter is not required to activate the pump.

Set the Tube Change Timer DIP switches with the number of hours you want the pump to run before the CHANGE LED is activated. When the set time is reached the change/level LED is lit solid red. The standby setting allows the tube replacement without disconnecting the pump.

Set the pump’s DIP switch  to stop or to continue to run when a leak is detected. Set the optional output relay to notify another device if a leak occurs.

The pump has three dedicated inputs to receive a signal from another device.
PULSE Receives a pulse from a dry contact water meter to activate the pump.
STANDBY Remotely start or stop the pump when a dry contact input is sent to the pump. Replace tube without disconnecting pump
LEVEL  Input from a fluid level device indicates a low level in the solution tank. The Level Input may be used with the low level output relay.

Specifications

Flow Rate Output                        Control  Fixed rate, interfaces with water meter
Reproducibility                            +/- 2%
Maximum Working Pressure          60 psi (4.1 bar)
Maximum Operating Temperature  104°F (40°C)
Maximum Suction Lift                    25 ft (7.6 m) vertical lift, based on water
Motor Type                                   Brushless DC motor
Shaft RPM (average maximum)      45
Duty Cycle                                    Continuous
Maximum Viscosity                        1500 Centipoise
Motor Voltage (Amp Draw)             120V 60Hz 1PH (0.6)
Power Cord Type                            120V 60Hz SJTOWA
Power Cord Plug End                      120V 60Hz 5-15P
Cord Length                                   6 ft (1.8 m)
Classification                                  Indoor / Outdoor

Materials of Construction

All Housings                                        Polycarbonate
Pump Tube                                          Santoprene®* (FDA approved)
Ball Check Valve Components                Ceramic ball (FDA approved); Tantalum spring; FKM seat & O-ring OR

                                                           Ceramic ball (FDA approved); Stainless steel spring; EPDM seat; Santoprene®* O ring

Pump Head & Guide Rollers                     Polyethylene
Roller Bushings                                       Oil impregnated bronze
Suction/Discharge Line                            Polyethylene (FDA approved)
Tube & Injection Fittings                          PVC or Polypropylene (both NSF listed)
Connecting Nuts                                      PVC or Polypropylene (both NSF listed)
Suction Line Strainer and Cap                   PVC or Polypropylene (both NSF listed); ceramic weight
All Fasteners                                            Stainless steel
Pump Head Thumb Screws                        Stainless steel; PVC
Pump Head Support and Transition Sleeve  Santoprene®*
Tube Pull                                                  PVC
Leak Detect Components                           Hastelloy®††; Stainless steel
 

Complete solutions are our specialty.

Our farming systems are equipped with brands we believe in. When it comes to providing the best products for farmers in our region, we have decades of experience, and we've seen our systems outlast the competition by years. Our goal is to save our customers from hassle and unnecessary costs on maintenance, power, and electricity in the long run.

Contact our product experts